Nitrogen Gas Booster Compressor for Tire Filling Nitrogen Gas Recovery Compressor

• Customization: Available
• After-sales Service: 1year, 1
• Warranty: 1year, 1
• Model NO.: GV-30/5~315
• Type: Scrap Metal Baler
• Automation: Automatic
• Certification: CE
• Product Name: H2 Gas Hydrogen Compressors
• Model: Gv-30/5~315
• Compressed Medium: 99.999% Hydrogen Gas
• Flow Rate: 30nm3/H
• Shaft Power (Kw): 461kw
• Inlet Pressure ( MPa): 5bar (G)
• Exhuast Pressure (MPa): 315bar (G)
• Cooling Method: Water Cooling Customized
• Speed: 400rpm/Min
• Performance: Low Noise
• Diaphragm Material: 00cr15ni5
• Application: Petrochemicals Compressor
• Valve Brand: Hoerbiger Valve
• Performance 1: Explosion-Proof Motor
• Motor Protection Level: IP 55; Temperature Rise Class B
• Transport Package: Wooden Package, by Sea
• Specification: 3200x1300x3150mm
• Trademark: 2800kgs
• Origin: China
• HS Code: 84148090
• Production Capacity: 200sets/Month

Product Description

The diaphragm compressor is a kind of compressor which have a special structure, good tightness. The gas can't contact any lubricant, so the cleanliness of the compressed gas is extremely high, and it's especially suitable for certain rare gas's compression, transmission, or bottling, and it also applies to corrosive, toxic, flammable, explosive gas. Widely used in the food industry, chemical industry, petroleum industry, mili-tary industry, air separation, manufacture, energy, aviation, etc.

Advantage:
1. High Compression Ratio
As a result of the optimized design of diaphragm cavity curve, maximum deformation of the diaphragm under allowable stress is ensured to obtain maximum volume efficiency;
2. Environmentally Safe --No leakage
Completely sealed, absolutely no leakage--suitable for use to compress gas in the radioactive area of the nuclear power plant and highly poisonous gas;)
3. 100% Oil-Free
Owing to the nonexistence of lubricant in the diaphragm cavity, that means it is impossible for gas to contact any lubricant, therefore can compress to the higher pressure of the dangerous gas and oxygen, fluorinated gas and chlorine, etc;)
4. High Product Purity
Compared to the compressors of other types, gas will not be polluted by the particles produced due to abrasion of sliding parts, therefore, it is absolutely ensured the same purity of compressed gas as that of the gas when entering the compressor. Therefore, it is suitable for high purity gas such as electronics, breathing gas, and hydrogen used in fuel cell technology;
5. Unique Design, Low speed, Lower maintenance cost 
Pressure lubrication is adopted for the compressor, so the moving parts of the compressor have excellent lubrication of hydraulic oil, which minimizes the abrasion of moving parts and reduce maintenance rate;
6. High quality supplement Oil pump
Pressure oil supplement is adopted for compressor, namely, the lubricant, after coarse filtering, is pressurized by passing through gear pump for fine filtering, then enter slippage pump, this kind of pressurized lubricating oil can prevent the occurrence of non-oiling due to the air existing in slippage pump; at the same time, it can prevent small particles from entering slippage pump to damage plunger, thus lengthening the service life of slippage pump.
7. High reliability, Alarm Device, energy saving
(1) The compressor is equipped with a diaphragm rupture automatic protection device, and the control system alarms when the diaphragm ruptures.
(2) When the compressor exhaust pressure exceeds the set pressure, the control system alarms. ensure safety and reliability of operation of the compressor;
8. Easy Installation, High-quality Spare parts, Safe operation
The bolts, nuts, and joints of the cylinder head are all surface treated; and oil pipes and coolers all adopt stainless steel pipe, providing the good appearance of the whole machine; Advanced oil-pressure valve is adopted for the display system, providing easy operation; Spare parts and after-sales service are provided in time for the whole service life of the product.
9. Good Cooler, High Efficient
The compressor has good cooling conditions. The oil cooler is equipped in the oil tank of compressor and water jacket is set for middle body, cylinder body and cylinder head, which provide good cooling for compressed oil and gas, thus improving the mechanic performance of compressor;
10. Independent electrical control system.
Adoption of modular design. According to the need of the user, serial crankcase and diaphragm head are selected to provide a wide range of pressure and flow;
11. Long service life 20years
12. Lower noise level

Production Name	150bar Oxygen Gas BoosterCompressor
Model	GV-20/4-150
Compress medium	100% Oxygen gas
Type	V type, Two-stage, two diaphragms,Single action, Water cooled, diaphragm compressor
Capacity flow rate	20Nm3/h
Suction pressure	0.4Mpa(4bar)
Discharge pressure	15Mpa(150bar)
Shaft Power	7.5KW
Driven method	Antistatic Belt drive
Suction temperature	Ambient temperature (0-45ºC)
Transmission temperature	≤50 ºC(after water cooled)
Water consumption	1.1t/h
Speed	400rpm
Main part material	Cylinder Head: 3Cr13, Gas Pipeline:304L; Diaphragm: 00Cr15Ni5 Flange: 304 steel
Cooling method	Water cooling ( note: the customers local water tower's working pressure should 0.2-0.4Mpa, and inlet temperature <35ºC)
Dimension	1550×800×1100mm
N.W Weight	1000kgs
Install position	Indoor or outdoor with shed
Noise	≤85dB(A) (within 1m distance)
Motor Information
Motor type	Y Series, Three Phases, Asynchronism
Motor Power	7.5KW
Motor speed	1450rpm
Voltage	380V/50Hz/3ph
Protection lever	IP54, Class F

Advantages of KEEPWIN Process Gas Compressor:
1.   High quality material, Stable & Reliable operation
2.  Low Maintenance cost & Low noise
3.  Easy to install on site and connect with the user's pipeline system to operate
4.  Alarm automatic shutdown to protection machine function
5.  Corrosion Resistance

Lubrication includes : Oil lubrication, low-oil lubrication and oil free lubrication;
Cooling method includes: Water cooling, and air cooling.
Installation type includes: Stationary and Skid Mounting.

Compressor parameters are detailed in "Reciprocating Compressor Data Table".
 

Model &Name:	DW-10.3/15-57 New Hydrogen Gas Booster Compressor
Structure:	D type, Two-column Two-stage, water cooled, Oil Free Reciprocating Piston Compressor
Comrpess medium:	H2: 88.1%    C1: 6.0%    C2: 3.5%   C3: 0.3%   iC4: 0.5%   nC4: 0.9%    iC5: 0.4%    nC5: 0.3%
Flow rate at suction condition	620m3/ h
Flow rate at standard condition	8460Nm3/h
Atmospheric pressur	945-964 milli bar
Suction pressure:	15bar (G)
Discharge pressure:	57bar (G)
Suction temperature:	-9~+42ºC
Discharge temperature:	≤110 ºC(before cooling)
Shaft power:	≤461kW
Shaft speed:	420 r/min
Dimension:	6770×3450×3250 mm
weight:	~16t
Altitude	487m
Relative humidity	64-83%
Compressor design refer standard	API 618
Painting color	can according to client's requirement to paint

Main Technical Parameters of Main Motor

Motor model:
Motor type:	Y Series, Three Phases, squirrel cage motor totally enclosed, Asynchronism, fan cooled suitable for direct on line starting at ambient temperature of 40˚C
Motor Altitude	1000m
Exproof protection level	EXD dIICT4
Motor power:	560KW
Rated Output power	not less than 110% of the compressor power
Motor speed:	420r/min
Motor voltage:	6kV (ACC.IEC34.1)
Frequency:	50 Hz (ACC.IEC34.1)
Startup mode	Direct Start
Protection level:	IP 55 (junction box IP55);   Cos Ø>0.85. Insulation class: F; Temperature rise: Grade B;
Terminal box location	Above
Direction of rotating	Both direction
Motor Cooling system	IC411

 

Inquiry to us!

Note:for the other customizing process gas compressor, please kindly send below information to our factory to calculate the producing cost for your item.
Clients' inquiries should contain related parameters 
A. The gas compression medium 
B. Gas composition? or the gas purity?
C. The flow rate: _____Nm3/hr
D. Inlet pressure: _____ Bar (gauge pressure or absolute pressure)
E. Discharge pressure: _____ Bar (gauge pressure or absolute pressure)
F. Inlet temperature
G.Discharge temperature
H. Cooling water temperature as well as other technical requirement.

D-type Reciprocating Compressor

D-type Compressor Specification Keepwin has developed models for 2D3.5,2D5.5,2D8,2D12,2D20,2D25,2D32,2D50 and 2D80 series reciprocating piston compressors.  which are stable,reliable and have already been in series and modularized.keepwin can aslo rapidly provide products of other specifications through  modular combination design upon users' requirements.  
Besides general gas such as air, the compressed medium may also include flammable and explosive gas, such Natural Gas and Coal Gas as well as special gas which are toxic and corrosive. KEEPWIN has taken a series of technical measures in aspects such as structure material, explosion prevention, anto-control and protection to guarantee safety and reliability. Products are widely used in variety of industries such as Petrochemicals, Fine Chemicals, Pharmaceutical Chemicals, Energy Chemicals, Machinery Industry, Electronics Industry, Agriculture, Animal Husbandry and Defense Industry, Astronomy, Aerospace, Medical and other fields.

 

D type Diaphragm Compressor Technical Parameters
No.	Model	Compressed medium	F.A.D (Nm3/min)	Inlet Pressure  ( Mpa)	Exhuast Pressure  (Mpa g)	Power  (KW)	Speed r/min	Dimension (L×W×H)mm	N.W  Weight (t)	Voltage V
1	2D3.5W-14/0.3~6	Regenerated hydrogen gas	14N	0.03	0.6	90	485	5200*1800*2500	8	380
2	2D3.5W-5.7/6.5	Regenerated gas	5.7N	0.02	0.65	45	485	5200*1800*2500	5.5	380
3	2D3.5W-17/0.4~12.5	Synthetic tail gas	17N	0.04	1.25	132	485	5200*1800*2500	5.5	380
4	2D3.5W-20/5	Feed gas	20N	0.002	0.5	132	485	5030*2000*2550	4.5	380
5	2D3.5W-25/9~49	Replenish hydrogen	25N	0.9	4.9	132	485	5400*3500*2200	8	380
6	2D3.5W-79/26~49	Recycle hydrogen	79N	2.6	4.9	160	485	5400*3500*2030	8	380
7	2D3.5W-20/0.1~6	Feed hydrogen	20N	0.01	0.6	132	485	4750*2200*2550	4.5	380
8	2D3.5W-54/0.02~0.5	coal gas	54	0.002	0.05	110	585	4560*1800*2550	5.5	380
9	2D3.5W-16.7/0.2~8	Synthetic tail gas	16.7N	0.01~0.04	0.8	132	485	4600*1950*2200	4.5	380
10	2D3.5W-36.7/0.3~2.8	Analytical gas	36.7N	0.03	0.28	160	485	4190*1800*2490	5	380
11	2D3.5W-82/12~22	Recycle hydrogen	82N	1.2	2.2	160	485	4300*1300*1740	5.5	380
12	2D5.5W-30/8	coal gas	30N	Micro positive pressure	0.8	220	585	3857*1528*2505	6.5	380
13	2D5.5W-40/8	Coke oven gas	40	Atmospheric pressure	0.8	250	585	3935*2020*2585	6.5	380
14	2D5.5W-40/8~111	Coke oven gas	40N	0.002~0.015	0.8	280	585	3935*2020*2585	6.5	380
15	2D5.5W-80/3.5~12.5	Rich gas	80N	0.35	1.25	280	485	4502*1750*1965	7	380
16	2D5.5W-72/2.5~8.5	Regenerated gas	72N	0.25	0.85	250	485	4040*1750*2380	6.5	10000
17	2D5.5W-30/0.1~7	Hydrogen	30N	0.01	0.7	200	485	4420*1750*2770	6.5	10000
18	2D8W-44/10.2	Reaction gas	44	Micro positive pressure	1.02	315	496	4828*1924*2750	8.7	6000
19	2D8W-65/8~25	Nitrogen gas	65N	0.8	2.5	250	490	4900*3645*2270	11	415

 Test and inspection
1. Part Material Inspection: Before shipment inspecting the mechanical properties and chemical composition of the following parts and provide inspection reports: cylinder, cylinder head, crankshaft, crankcase, main bearing, connecting rod, piston rod, piston rod, cross head, connecting rod bush connecting bolt, cross head pin, etc. 
2. Nondestructive inspection: the supplier shall perform non-destructive inspection of the following parts.
Hydrostatic test and pressure test
The test pressure of cylinder block, cylinder head, piston and other compressed parts is at least 1.5 times of the maximum allowable working pressure, and lasts more than 30 minutes. The test pressure of the above parts of the water chamber is at least 1.5 times the maximum allowable working pressure, not less than 0.6MPa.





Our services:
Keepwin Provides Top-Rated, Efficient Reciprocating Compressors And Parts. Energy Efficient. Industry Leading Warranty. Low Maintenance. Gas Solution Engineer and Easy Install, promises to give a definite reply within 6 hours for the after-sales product service, can provide overseas Installation service. We can customize all kinds of standard air compressor, flammable gas compressor, toxin gas compressor of reciprocating compressor & diaphragm compressor.

What is advantages of our company?
Right Compressor Right Solution Gas Engineer Company
Whether centrifugal, screw or reciprocating, Keepwin is the sole multi-compressor provider for you.
The Best Quality, The Most Reliability
What is need to consider when purchase a correct compressor Upgrade Your Gas Compressor to Save Money & Energy Consumption Gas compressors are a vital part of many industry applications.
Save money and energy in your industrial workplace by upgrading your gas compressor today!

     


FAQ
Q1: What's your delivery time?
A: Generally for standard air compressor is 15 days if there are stocks with regular 380V/50Hz/3ph.
    Special customizing compressors with 30days production date for Screw Compressor, 90days for diaphragm compressor & reciprocating process gas compressor.

Q2: How long is your air compressor warranty?
A: Usually 1 year /12 Months for whole compressor machine, 2years/24months for air end (except maintenance spare parts.). And we can provide further warranty if necessary. 

Q3: How long could your air compressor be used?
A: Generally, more than 10 years.

Q4: Can you do OEM for us?
A: Yes, of course. We have around two decades OEM experience.And also we can do ODM for you.

Q5: What's payment term?
A: T/T, L/C, D/P, Western Union, Paypal, Credit Card, Trade Assurance and etc. Also we could accept USD, RMB, GBP, Euro and other currency.

Q6: How about your customer service?
A: 24 hours on-line service available. 48hours problem sovled promise.

Q7: How about your after-sales service?
A: 1. Provide customers with intallation and commissioning online instructions.
2. Well-trained engineers available to overseas after-sales service. 

Q8. Are you factory?
A4: Absolutely! You have touched the primary sources of Air /Gas Compressor. We are factory.

How to contact with us?
Send your Inquiry Details in the Below, or Click "Send inquiry to supplier" to check more other Gas Compressor machine equipment!